Wednesday, June 27, 2007

C-Ski 440 by Steve Ellis

"Spumbu" C-Ski 440 made by Steve Ellis at Fibre Tech

At a Glance: The C-Ski 440 by Steve Ellis is an impressive boat, very 'clean and simple'. I think you would have to be a seasoned spearfishermen to appreciate its design. It comes without the flare and finished you find on show room floors.
But having designed and built a boat, I understand it to be functional design. I will let you in ona little secret.... I copied much of what I saw Steve doing when I designed my boat.

First Impressions: Lets take a look at the C-Ski 440's layout. If you are looking at the C-Ski with a center console then this what you will get.
Starting at the transom there is a small hatch, big enough for a yellow safety can and life jackets etc. It is quiet deep and any thing you dont want fish on can go in there.
Next is the center console, the battery lives in here and there is some space for some extras. There is enough space on the center console for a gps / fish finder and compass. The steering and controls will be up to you to decide on ... and thats another whole discussion.
The fish (main) hatch is nice and big, it was designed for spearfishing. Steve is an experienced spearo and designed the boat to suit the needs of spearfishermen. Thats why when you look at most smallish boats designed for fishing the hatches are frustratingly small.
The fuel hatch takes one 25l standard fuel can (the flat one you get with the motor). There is space for a small 10l or15l spare.

The Testa: I was recently up in Mozambique and Iain Ewing brought his C-Ski 440 with. We had fairly good conditions, but did have the odd trip in some serious weather. So I think I have a pretty good idea of how the boat preforms on the water and its practicality for Spearfishing.
The ride for a small boat is excellent, look there was the odd chop that the boat did bounce a little and the occasional spray of bow water. But I have been on most small boats available and this is the one that stands out.

Three of you were on the boat and one must remember Iain is no small chap. This did mean that we had to be conscious of each others movements on the boat. Especially when getting on and off between dives. The C-Ski is only 1.75m wide and being a mono hull does roll a little. There are very few small boats that dont roll, and normally the ones that dont are flat hulls and are terrible on the water.

The sides are low in the water (check the pic of Spumbu on some other trip in Mozam) This makes getting on and off very easy. Some water does wash over the back but this is seriously not an issue, as there is nowere for the water to sit and drains off quickly. Even in the surf, the boat holds very little water on the deck and does not get bogged down at all.

The deck space and functionality of the C-Ski is very good. We each had 2 or 3 guns and all our kit. Everything stashed away nicely in the gunbags and in the main hatch when launching and coming in. The only thing is that we had to have a spare 25l fuel can on the deck. I think this the only place that needs attention. We were traveling long distances and had to change tanks every day. Perhaps there should be space for 2 x 25l standard spuggs in the fuel hatch?

Overall Impressions:
You can understand why so many seasoned spearo's land up owning one of Steve's C-skis. It's just so functional, no frills gonna do the job boat. I would say it is probably the best boat in its class. (3man single motor boat) There are some great hulls out there, but Fibre tech seems to be the only one making this size boat at the moment that works.

I did some sums the other day for a guy for whom I am organising a boat for through Steve and the total cost came to R75 000. But thats for everything from start to finish, with all the bells and whistles. It seems allot but if you look at what else is available and you find your self coming back and having another look.

The costs worked out like this:
Basic Boat - R19 500
Extras -R 9825 (center console, controls, keel strip, covers ect)
Trailer - R 10 800
40 Yamaha - R29000

If you want to go with 2 motors the boats and cost sky rocket into the R100000.00 range very quickly, so thats another ball game altogether.

Would I own one? ........ For sure!


See the new Fibretech C-Ski 444 Here

Tuesday, June 19, 2007

Freedivers Aqua Glide Chicle Wetsuit Top

At a Glance: During late winter last year while picking up stock from Freedivers Shane showed me his Aqua Glide Chicle wetsuit hooded jacket. I had seen guys using them and had always wondered what the attraction was.

The neoprene that suit is made from is ultra soft and stretchy5.5mm Yamamoto Chicle neoprene, which has no nylon material on the outside. It is smooth and is designed to dry quickly in the wind making it ideal for boat diving.
I could see how the suit would be warm and comfortable. But warning bells went of on the durability of the suit. Shane however convinced me to try one ......

First Impressions: Being a very fussy person I did not think the guys at Freedivers would get the wetsuit right first time. But to my surprise the hooded jacket was so snug and comfortable, molding to my body perfectly. I was again surprised at how maneuverable I was even more than a standard double nylon 3mm suit and this was 5.5mm of neoprene!
Shane ran through how to care for the suit and I was on my way.

I cant really remember the first dive in the Aqua Glide top, but I do remember being so snug and commenting to my mate that it was like waring a warm jersey. It was so good, I cant remember diving in anything else until late November

The Testa: Over a couple months of seriously hard diving, mostly shore entry chicle neoprene wetsuit top was starting to prove its self. On the comfort and warmth side there is nothing you can say against the suit, all the glued seams were holding and did not show any sign of failing.
I had started to collect some nicks on the back from carrying fish along the beach and my spear had made a small tear on my arm. All of these were cosmetic and the small tear fixed with some wetsuit glue.

But one Saturday morning in late November I tore the suit. The sea had warmed up considerably and the day turned into a stinker. The Cuta had turned on and I pushed a long dive to the point of exhaustion. Getting back to the beach some 2km from the car and a hand full of cuta on the stringer, I decided to take the top off and not bake in the already overbearing heat.
Not thinking I tried to take the suit off as per usual and tore open the back. While sorting all my kit out on the beach the suit had dried stopping it from sliding on itself. Usually I wet myself down and fold the bottom up and full it with water, then there is no problem.

The suit was fixed, and have had no problems since. I suppose that could be the up side of stichless suits is that a little bit of glue can fix anything. (I would take it to Shane to fix they will do a better job and have some glue that is amazing, way better than the off the shelf stuff.)

Overall Impression: The Aqua Glide suit for me is the next step up in wetsuits. Remember when you first started diving in an open cell suit, and you felt so comfortable and warm vowing never to go back to a double nylon suit? Well diving in this suit is much like that, not that I would never dive in my standard open cell suit again - because of practical reasons. Its just that I wish I could dive in it all the time.

The Chicle neoprene suit has a specific purpose, and like any specialist piece of equipment if you use it in the wrong application you will land up abusing it and it will not last. Crayfishing is one of those areas, you cant go wedging yourself in a barnacle infested crack to pull some buggs and expect to come out unscathed!

If you do allot of boat diving, or don't really catch crayfish this is maybe an option. I feel the cold real easy, I even get cold in summer! And this suit has been fantastic in terms of warmth.

  • Super comfortable
  • Probably the warmest suit you can get.
  • Excellent for boat diving, as the it drys quickly and does not chill in the wind while traveling. So you don't need to take a windbreaker anymore.
  • Made locally - previous chicle suits were all imported with little or no backup service.
  • Not a 'tough' suit (keep in mind its purpose)
  • You need to look after it
  • Use loads of lubrication when taking on and off. This (for some) is a mission but worth it. Conditioner works better than shampoo, and aqueous cream is also good. I sometimes use a mix half aqueous cream and conditioner.
  • Dry the suit inside out, and out of direct sunlight. My suit started to grow moldy from never drying properly ...... might have been because I was diving every day.
Interesting Facts:
  • Yamamoto Neoprene is used by Picasso, Elios and other leading wetsuit manufactures.
  • Yamamoto Neoprene is not manufactured from petrol, but from limestone, which contains up to 99.7% of calcium carbonate.
  • Giving The wet suit a more even density of the neoprene (better insulation, better buoyancy, material resistant to compression damage)
  • Higher elasticity similar to that of human skin, thus adding extra comfort.

Friday, June 15, 2007

Rob Allen Ghost Leader Flasher

At a Glance: The Rob Allen Ghost Leader Flasher or the Inline Flasher just looks like another gizmo to clutter the dive bag. That said I am a flasher freak, during summer I dive with more Bling than some ghetto pimp rapper busting some gangsta hip hop in some seriously iced up jewelry. So a couple months ago when I feasted my eyes on the ghost leader flasher which was still in the experimental stages I was immediately curious. After a little bit of persuading, Jeremy Williams of the Dive Factory parted with his one. And ...... well I have not looked back.

First Impressions: One my first dive I realised had something special, however this is not going to be for every spearfisherman. I quickly found that if you like your kit simple this will not be for you. The rotating metal propellers hook your line quiet easily, and getting the line off your gun after swimming through the surf can be a bit of a trick. (I have found some solutions ....will tell you about them later tho.)
That first dive I did not see any fish and the buoyancy on the ghost line was wrong, but I could see the potential. In my mind I could almost see the Cuta swimming in on me.

The Tester: My first real taste of the potency of this flasher came on a recent trip to Mozambique. The Ghost Leader Flasher had had some mods since I first used it. There were now 2 floats on the line and they were positioned about 5m from the flasher allowing the flasher to sit 5m below the surface when resting. Not very deep, but better than it being on the surface.
This how my rig was set up for that trip:
From the gun I had a 3m bungie (which I later replaced with a shorter one, to bring the flasher closer to me), then the Ghost Leader Flasher which was set up with 5m of ghost line then the 3 spinning flashes on stainless cable, and another 5m of ghost line with the 2 floats. I then had a 5m bungie going onto my buoyline.

Again I realised that this added a curve ball to the equation, taking that extra time to wind up and unwind ever time I got on and off the boat.

That said the fish I had come in on me was amazing, and even though the vis was not great and the fish not thick. 70% of the fish I shot were coming in on the flasher above my head. One of the guys on the trip even commented that he could hear me working the flasher from the surface as the propellers whirred in the water.

It was also great to watch the response of the Kingfish, they would be disappearing into the gloom and one or two pulls on the flasher and they would do an about turn and come back.
I even had a cuta come back on me, I had dived down and saw a cuta swimming off in the distance too far away to even chase. Leveling out I worked the flasher only to see the Cuta turn around and commit 'Taliban' as it swam literally onto my spear.

Overall Impression: It is totally new dynamic diving with the Ghost Leader Flasher, I am used to shooting most my fish from above or on the same level. Now the fish come in and you land up shooting up at a 45 degree angle. For some reason I have found that the Cuta are quiet skittish (or just excited) when coming in and dont like to be chased from this angle.
That said if you take aim without hesitating, you can normally hit the fish with out having to swim towards the fish.

I don't think this will totally replace the traditional flasher, but it does give that extra edge to your diving. I have gotten so used to diving with the inline flasher that it has become part of my standard setup. And now as winter has approached I would have usually not taken a flasher as the cuta thin out, now I always have one. This payed off a couple weeks ago when a 20kg Cuta came near the surface to take a look at the flasher working behind me as I swam up the current. The fish promptly swam right underneath me 'Taliban Fish'.

The pro's and con's:

Basic Pro's
  • You draw the fish to you while on the bottom.
  • don't have to keep swimming after your flasher float.
  • It is part of your gear, not something else you have to swim with.
  • It can be a hassle, hooking your buoy line.
  • Having to carry the extra fish up the beach :-)
  • Wind up only the ghost line on your gun, tie the rest of your buoy line up. This will reduce the line getting snagged.
  • I have found that the flasher works best with a long bungie to help floats as the bungie cord is buoyant. This means that when you pull down the flasher returns towards the surface quicker, creating a better action. This said I am currently diving with no bungie (simple rig) and it works fine.
  • When on the bottom face with the current that way your flasher is slightly in front of you, and you are facing towards the fish swimming up current.
  • The Ghost Leader Flasher also works great with a reef hook and reel gun. Find your favorite drop-off or pinnacle, hook up on the current side and dive around the flasher working in the current.
In Parting: Rob Allen's Ghost Leader Flasher is definitely something to try out.


Monday, June 11, 2007

Mares X-Vision

Mares X-Vision Spearfishing Mask

This has to be my favorite mask, the X-Vision by Mares has served me well over the last 3 or 4 years. I have tried many masks but always come back to tried and trusted mask.

I used to dive with the Super Occio by Cressi but once I moved over to the large vision of the X-Vision I found it almost impossible to go back. And here is the strange thing, the X-Vision has a very low internal volume. In Fact is lower than most so called "low volume" masks. There are some that are lower, but they dont have nearly as big area of vision.

The silicon that the skirt made from is especially soft, and this combined with fact that the strap is attached to the skirt and not the frame makes the X-Vision extremely comfortable. There are many rip offs / pirate versions of the X-Vision but they are inferior mostly because the materials are not the same quality.

Although the X vision is more expensive than some other popular masks I am yet to have an unhappy customer. I can recommend this mask with confidence, it is just the most fantastic mask.

I did however try the "upgrade" of the X-Vision the
Pure Vision from Mares. This was a disaster of note.
read Coatesman's Report

The mask has excellent vision, even better than the X-Vision. But there is a design flaw and the mask leaks. I know that this is not an isolated incident as my supplier tells me that the first batch almost all the masks came back.

They had supposedly 'fixed' the problem but that does not seem to be the case. Very strange that Mares would release a faulty product on the market.

So for now I would recommend the Mares X-Vision to almost any diver regardless of the level of experience.


Thursday, June 7, 2007

Rob Allen 1.4m Tuna Rail Gun

Rob Allen 1.4m Tuna Rail Gun

At a Glance: The Rob Allen 1.4m Tuna Rail Gun is a fine piece of workmanship, the attention to detail stands out. This real gives you the impression that you have a quality product in your hands. That aside the spear is slightly thicker 97.5mm) than the Caranx or other standard guns. And the grip is slightly less bulky than the old handle ... or at least it feels that way.

First Impression: The first time I shot the gun was in Mozambique, and on my first dive down on the trip new gun in hand a Cuta swims in onto me. Slightly nervous I take aim and spine the cuta. I swim to the surface on my first dive on the trip with a 15kg cuta ... of course I am going to smile. So my first impressions were good.

I did however tweak some things, I shortened the rubbers a touch being careful not to overpower the gun. And as always I put a double wrap shooting line. At first the line release did not really handle the double wrap, but Rob gave me an upgrade which is working perfectly now.

The Tester: The big test came on morning on the same trip in Mozambique (read more on that Mozambique Spearfishing Trip) when in the distance I saw what I thought was a 20kg Giant Kingfish. At first I was not going to take a shot, but I eventually took aim when it came a little closer ... now I thought it could be 25kg. Truth was that it was quiet far away and when I took the shot it seemed like the spear took forever to reach the fish. I was at first concerned that the spear did not penetrate all the way through, but after being dragged around the ocean I realised the shot was good. In fact the shot landed exactly where I was aiming, and the combination of the double latex bands and the thicker 7.5mm spear meant there was enough velocity to hit the fish hard. What also impressed me was that the spear was still dead straight after shooting the 43kg Kingfish. I have had smaller kingfish fold my spear in half before.

Overall Impression: So far I have not had a bad shot with the gun other than when I have relaxed too much and the recoil has made the shot hit high on the fish. This is something to watch out for with any double rubbered or high powered gun. But that said when concentrating and keeping focused the gun is extremely accurate, even near the end of the double wrap. I have shot some smaller cuta in crystal clean water from silly distances, once I even hit a very small cuta stone dead right at the end of range. The barb did not even get into the fish, it just went like an ironing board and sank nose first.

This gun is one of my favorite guns, unfortunately it is a tool for a specific purpose and I don't get to use it as much as I would like. I have been asked the question would I prefer a carbon rail as apposed to the aluminum rail. And after using both I have found that the heavier metal barrel has less recoil and if there is any flex in the barrel it does not seem to be affecting the guns accuracy. So if you are looking at getting a blue water gun the Rob Allen 1.4m Tuna Rail Gun is a well balanced Speargun, something worth investing in.


Wednesday, June 6, 2007

FreeDivers Evolution Reel Gun

The Free Divers Evolution Reel Gun.

First Impressions: This is not a flashy speargun, in fact this one is even void of all the colorful stickers. And only has some grey type down the barrel with a grey handle insert.

The new Evolution rail is impressive- sleeker than the older sleeve, and the rail is even deeper. The new barrel also has internal reinforcing ribs to eliminate barrel flex. The 1.2m speargun comes standard with 18mm natural latex rubbers and a 7mm spear.

The focus however is on the reel, it looks seriously robust! And with its simple design very little, if anything could go wrong. This reel had black nylon braid as apposed to the more expensive dynema.

Short Term Impressions: My first dive with the gun was a good one, we went down the south coast and I landed 3 good cuta 14, 10 and 8kg
Go check out the story Hiberdene Gets clean

I have used the gun over the last month all my shore dives and have found great freedom in diving untethered with my buoy line clipped off and fastened to the reef with a reef hook.

After numerous dives I would say that there is nothing I can say that is bad about the product. I did make some alterations .... nothing in my kit is standard!
I double wrapped the shooting line and put an longer bungie on to help ease sudden pressure on the spear and line. I shortened the rubbers slightly ... I like a little more power, but thats not to say the standard setup would not work.
The gun is very accurate, the only fish I missed were fish I took fliers at, but everything I had an opportunity to aim at got hit.

Overall Impressions: The FreeDivers Evolution Reel Gun definitely has a place in my dive kit. And at the price I don't think there is better value for money. I was impressed with the reel, so far I have had not one hint of a tangle and the reel cover means you just wind the line in and you dont have to feed it onto the reel like the open ones. Some people wil say the speargun is best suited for reef fish hunting. I beg to differ ...... a 20kg cuta says it all.